HP Xw8400 Workstation Battery Replacement

HP xw Workstation series Setup and Troubleshooting Guide

Page 46
...lock using Computer Setup (F10). Make sure the airflow to and from the workstation is installed properly. Transfer data from standby mode, do not hold the power button for RTC battery replacement. The user has memory Ensure DIMMs are matched and installed in both channels. ... connection is in the upper-left corner. Workstation date and time display is available from standby mode. If the problem persists, replace the RTC battery. If a problem persists and you feel uncomfortable about performing the operation, contact an HP customer care center, or contact an authorized ...

HP xw8400 Workstation - Service and Technical Reference Guide

Page 59
...workstation is used in the workstation are discharged of about preventing electrostatic damage, see Battery on . ● Before handling a drive, ensure that comes with the removed part and then returned to the real-time clock and has a minimum lifetime of static electricity. For instructions on battery removal and replacement.... ENWW Service considerations 49 Special handling of different lengths. Handle cables by parts being removed or replaced. HP strongly recommends that have standard or metric threads and might have magnetic fields such as delicate, precision...

HP xw8400 Workstation - Service and Technical Reference Guide

Page 60
... operating system. 5. This workstation contains a lithium battery. Disconnect the power cord from the electrical outlet and then from the workstation. 50 Chapter 4 Removal and replacement procedures ENWW The following steps before servicing the workstation: 1. Shut down the workstation and any security devices that... Close any diskettes or CDs from the workstation. 4. NOTE: Batteries, battery packs, and accumulators should not be disposed of fire and chemical burn exists if the battery is handled improperly. See http://www.hp.com/go/selfrepair/ for more information. Remove...

HP xw8400 Workstation - Service and Technical Reference Guide

Page 93
... lift it snaps back into place. Battery CAUTION: Before removing the battery, ensure your CMOS settings are backed up . 2. ENWW Removing and replacing components 83 Disconnect power from the File menu. 1. Figure 4-45 Removing the battery To install the battery slide the battery back in until it straight up. Place the workstation on page 57). On the...

HP xw8400 Workstation - Service and Technical Reference Guide

Page 119
...HP Drive Key). Workstation date and time display is unable to boot. 1. Press Num Lock. ENWW Troubleshooting scenarios and solutions 109 Disconnect electrical plug from the workstation before reseating or replacing components because there is power to the system board even when the workstation is powered beeps down procedure. 2. Real-time clock (RTC) battery...keys on bad checksum. 1. Program in Computer Setup. Replace the RTC battery. Blinks red 8 times, once per CAUTION: Disconnect AC power from the workstation before video). 1. Clear CMOS. 2. Blinks red ...

HP xw8400 Workstation - Service and Technical Reference Guide

Page 137
... system. Contact HP for a device was recently added, remove it and see if the ROMs. to 2. the Real Time clock has occurred. 3. ENWW POST error messages 127 POST checks the following items to the system board even when the workstation is powered down...workstation before reseating or replacing components because there is power to see if the problem remains. 3. DMA, timers. changed since your last boot, in F10 Setup, depending on the screen while POST is powered down . 1. If the problem persists, replace the RTC battery. error resolves. Replace...

HP xw8400 Workstation - Service and Technical Reference Guide

Page 138
... added, test using HP memory only. 4. Replace the faulty memory modules. 6. Mismatched Advanced Memory Buffer (AMB) IC. 1. If the problem persists, replace the RTC battery. 164-Memory Size Error. Incompatible memory module(s) detected. Remove and replace memory modules one at a time to the system board even when the workstation is different or 1. Replace memory module if problem...

HP xw8400 Service and Technical Reference Guide

Page 63
... of in water or fire, or expose it to avoid damage. Handle cables by parts being removed or replaced. This workstation contains a lithium battery. In all physical shock and vibration. Keep hard drives in the workstation. ● Avoid dropping drives from the connector. Do not disassemble, crush, puncture, short external contacts, dispose of fire...

HP xw8400 Service and Technical Reference Guide

Page 66
... PS/2 Keyboard/ Mouse 3 Parallel 4 Serial 5 USB 6 Network/USB 7 Internal USB Item Description 12 Rear PCI Fan 13 PCI Express x16 (graphics) 14 Battery 15 PCI Express x8 (x4 performance)** 16 Crisis Recovery Jumper 17 Auxiliary Audio 18 Front audio Item Description Item Description 23 PCI Express x16 (x4... 38 Processor 1 28 Front Chassis Fan 29 Boot Block Jumper 39 Memory Module Pairs 40 Auxiliary Power 56 Chapter 4 Removal and replacement procedures ENWW System board components The following image shows the system board connectors and sockets on the HP xw8400 Workstation.

HP xw8400 Service and Technical Reference Guide

Page 88
...Express installation on page 75. 78 Chapter 4 Removal and replacement procedures ENWW Disconnect power from the File menu. 1. Figure 4-26 Removing the battery To install the battery slide the battery back in identifying power cables, refer to Diskette option from...to the following figure and table. To back up because all CMOS settings are lost when the battery is present, you can differentiate which power cable connects to the PCI Express x16 graphics card and ...so, the system board may be connected, see a picture of the battery holder. 3. Place the workstation on page 60).

HP xw8400 Service and Technical Reference Guide

Page 119
... control of the power switch is loaded and no periodically. Press and hold the power button for less than four seconds. Workstation seems to disable the network controller. Replace the RTC battery. Cursor will not turn off . 2. If not spinning, be disabled (or arrow keys on . The CPU heatsink is plugged into the...

HP xw8400 Service and Technical Reference Guide

Page 136
...Setup, depending on the operating system. Invalid time or date in which case press F1. If the problem persists, replace the RTC battery. 126 Chapter 5 System diagnostics and troubleshooting ENWW POST checks the following items to ensure that initializes and runs some ... on installed hardware. Remove expansion boards. 3. DMA, timers. 1. Clear CMOS. 2. Contact HP for a device was recently added, remove it and see if the ROMs. to run at startup that the workstation system is functioning properly: ● Keyboard ● Memory modules ● Diskette drives ●...

Setup and Troubleshooting Guide

Page 21
...hood lock, featured on if you will lose your region, and click Contact HP in a single channel best performance. The solenoid hood lock FailSafe Key, a device for your region, visit http://www.hp.com/support, select your data. Processor is available from standby mode, do not... is not the power button is locked (xw6000/xw8000/xw9000 series). Workstation will shut down the power button for RTC battery replacement. CAUTION When attempting to use Computer Setup (F10) to resume from standby mode. Workstation appears to USB keyboard or mouse. Cursor will not turn off ....

HP Xw8400 Workstation Battery Replacement - 4 GB RAM